Complete User Guide on Electric Skateboards | Skatetek

OWNER’S MANUAL

Preface
Riding Instructions
Maintaining your Electric Skateboard
Important Safety information

Preface
1. Inspect outer carton for damage and report any to your freight carrier or dealer.
2. Open carton and inspect for internal damage, report any to your freight carrier or dealer.
3. Remove your new Electric Skateboard, remote controller and charger.

Riding Instructions

Before riding your new Electric Skateboard, please be sure you fully understand how the model you have purchased operates.

IMPORTANT

The electric Skateboard’s wireless remote uses a unique 3G high frequency radio signal (Bluetooth) for short distance communication, and a one on one coding function between the remote control and the PCB switchboard minimized the possibility of signal interferences. Signal interference may occur under a strong magnetic field. Use caution and check your ride area for signal interference before use.

The Electric Skateboard Troubleshooting If you take off and refit the battery, and the power light is not on, please check the battery to see if it has adequate power and is fixed properly. If they are ok, that means the self-protection has started. There is nothing wrong with the skateboard. When the battery terminals touch the control box terminals, the capacitor on the PCB of controller will be charged by the battery immediately and a momentary short-circuit occurs, so the self-protection kicks in. Just remove the battery and refit. (You may have to repeat this several times). Try not to take off the lithium battery frequently when the skateboard is in service, because when frequently removed and then refitted, the battery is heavy on the terminals. The terminals can be burnt out easily and an electric arc could be generated at the connection section to melt the conductor terminals, which can lead to damage to the battery or controller.
Lithium battery has a double protection system: a. Current-limiting protection. When the current value reaches the set level, the protection system will kick in for the protection of the electronics and will stop all power from your board.
b. Short-circuit protection. In case a short circuit in the controller, motor or battery occurs, protection system will be started for self-protection and power will stop. c. In most cases removing the battery pack and fitting will reset your board and restart it.

Pistol Grip Remote Controller

1. The Pistol Grip Remote Controller regulates the speed of the board. Pulling back on the lever will accelerate the board. Releasing the lever will return it to the neutral position. Pushing forward on the lever will brake.
2. After standing on board, pull the power lever. Your Electric Skateboard will start slowly and build speed as you hold the lever back.
3. To decrease speed, let the lever go. This will slowly decrease your speed. To slow quicker, push the lever forward to brake. Maximum speed and stopping distance depends on your weight and riding surface.
4. Know your limits. Start slowly and keep your speed down until you have mastered controlling your ELECTRIC SKATEBOARD.
5. Read the section titled: “Riding your Electric Skateboard before attempting to ride”.

Instruction for The Power Hand Grip Controller

A. Status light.
B. Coding hole. Use a pin like object (avoid the metal made pick stick) to push down the button inside the hold to sync the controller and the skateboard.
C. The on/off switch of the Trigger controller
D. Reverse button. By pressing this you regulate which direction the board takes. The Skateboard has to be at a complete stop in order for the reverse button to work. When you want to reverse, just flick the switch and then squeeze the trigger. When you want to forward again, press the reverse button again and then push the trigger, Each time you press the switch, the board will reverse direction.
E. The battery cover. Squeeze downwards first and then remove the cover to the direction shown. Match the positive and negative signs when replacing the battery inside.
F. Pull trigger backward for acceleration, Let it go for neutral, and push it forward for braking.
G. Speed limit pick. Basically, we set it at a slower speed gear. You can also limit the speed gear by shifting the pick to the faster speed gear side.
Control Box for 1200W
H. On/off switch for the skateboard
I. LED power light.
J. Coding Hold. You need to use a toothpick-like device to push the button inside the whole when you are syncing the board with a controller.

How to Sync 1200W

1. Turn on the skateboard
2. Use a toothpick to poke down I and you will see H blinking.
3. Turn on the trigger remote controller, and then use a toothpick again to poke down B.
4. Turn the trigger remote controller off and then turn it on again, then it will work.

How to fit a new control box

Flip the board over and connect all wires, then turn on the power, First of all, you need to press the small button(control box reset button), depicted on the picture, on the controller PCB and put the drive wheel on your left side. By standing next to it after turning on the board, you should see the drive wheel turning counter-clockwise. If it is not turning in the direction, press the button again to see if the drive wheel runs counter-clockwise. Make sure the drive wheel runs counter-clockwise before your sync.

Riding Your Electric Skateboard

BEFORE YOU RIDE

Be sure that you are thoroughly familiar with all of the features and controls discussed in the previous sections. All safety equipments should be worn, even when riding for short distances or durations. Make sure that the area in which you plan to ride is paved, level, free of obstacles, and not crowded.

SAFETY WARNING

You are able to climb abroad a powerful motorized skateboard. If you have doubts about your ability to ride, DO NOT RIDE IT! Know your limits and ride within them. Even if you are an expert skateboarder, give yourself time to learn the Electric Skateboard and ride conservatively, especially the first few times. Remember, the Electric Skateboard is silent and others will not hear you coming. Give yourself adequate time and distance to stop and avoid obstacles and others.

GETTING STARTED

Make sure the switch to the ELECTRIC SKATEBOARD is “ON” and the switch on the hand controller is “OFF”. Step onto the skateboard and assume normal skateboard stance. Keeping your fingers off the power lever, turn the switch on the top of the controller to the “ON” position. Pull the lever or tap the first finger button for a moment to start the board. Start off slowly by pulling the lever back or remaining in the first tap speed until you become comfortable and are in control of the speed.

Uphill and Downhill Riding

The ELECTRIC SKATEBOARD is far superior to an ordinary skateboard in uphill and downhill riding. On an uphill run, you will find that you need in keep your weight over the rear wheels to keep them from slipping. If the hill is too steep, the board will bog down and continued use may overheat the motor. Stop, step off and walk the steep hills. This board will take lighter riders up hills faster and will slow down as the rider’s weight increases. Take advantage of the reverse and place the driving wheel in front when you are riding uphill. The power board runs more efficient uphill when the driving wheel is in the front. On downhill runs, the motor remains engaged at all times. Providing same drag or button to slow. You also have hill breaking control. Frequent minor speed corrections with the brakes are preferable to letting your speed build and then breaking suddenly. KNOW YOUR LIMITS AND RIDE WITHIN THEM!

SPEED

NEVER RIDE DOWN HILLS THAT ARE TOO STEEP TO MAINTAIN SAFE TO YOUR ELECTRIC SKATEBOARD. NEVER RIDE DOWN HILLS THAT REQUIRE CONSTANT BREAKING, AS THAT CAN DAMAGE THE BOARD’S ELECTRONICS.
Turning your Electric Skateboard
The Electric Skateboard turns like any other skateboard. Apply pressure to the deck with your heels or toes and the board will turn in that direction. More pressure will result in tighter turns. IF the hands of experienced rider, the ELECTRIC SKATEBOARD is capable of making a complete 180 in a 10” radius Do not try to make turns at full speed. Always SLOW DOWN

Maintaining Your Electric Skateboard

MAINTENANCE WARNING

FAILURE TO FOLLOW MAINTENANCE INSTRUCTIONS AND GUIDELINES WILL VOID YOUR WARRANTY. DO NOT OPEN BATTERY BOX. DOING SO WILL VOID YOUR WARRANTY.

Routine Maintenance

Under normal use, your ELECTRIC SKATEBOARD will require very little maintenance. Check all fasteners for tightness before every use, especially if used on an irregular surface. This will require an Allen Wrench and a few different sized sockets or open-ended wrenches. YOUR ELECTRIC SKATEBOARD is not waterproof and must not be ridden in the rain, mud, or other wet areas to prevent electrical damage. Always keep your board clean and free of moisture.

Drive Wheel Replacement

It is normal for the drive wheel to wear faster than the other wheels. DRIVE WHEEL REPLACEMENTS ARE available from Skates or our Dealers.

Drive Belt Replacement

Due to the superior design of the Electric Skateboard the drive belt will last a long time, but eventually will wear out. Replacements can be ordered from Skates or our Dealers.

Wheel Replacement

As with any skateboard, the wheels of the ELECTRIC SKATEBOARD will wear out with use. Replacement wheels, bearing, and spacers are available from Skates or our Dealers.

Rubber Bushing Replacement

Although specially formulated for extremely long life, the rubber bushings located in the trucks of your ELECTRIC SKATEBOARD will wear over time. It is recommended that they be replaced with the same special bushings that are standard equipment on the board. They are available through Skates or our Dealers.

Battery Maintenance

The rechargeable Lead Acid Battery that powers your Electric Skateboard should last 1-2 years if kept properly charged, but will slowly decrease in capacity and eventually fail to hold a charge. To maintain maximum life, always keep your Electric Skateboard charged when storing for extended periods of time. Plug it in once a month to maintain a charge. They are easily replaceable using without any Replacement Kit. Lead Acid batteries are available from Skates or our Dealers.
The rechargeable Lithium battery that powers your Electric Skateboard should last 2-5 years if kept properly charged, and it will not slowly decrease in capacity or eventually fail to hold a charge, but it will decrease 10% to 20% in capacity after more than 500 charges. To maintain maximum life always keep your Electric Skateboard charged when storing for extended periods of time. Plug in once in three months to maintain a charge when you are riding your power board. They are easily replaceable without a Replacement Kit, Lithium batteries are available from Skates or our Dealers.. DO NOT PROP UP YOUR SKATEBOARD FOR STOREAGE, LEAVE IT ON LEVEL GROUND.

Repair Information

Many repairs that may be required for your Electric Skateboard are covered in the maintenance section of this guide. Should your Electric Skateboard require repairs that are not covered under this section, contact Skates with the nature of the problem.
Skates provides a warranty for your ELECTRIC SKATEBOARD for 90 days from the date or original purchase against manufacturer’s defects in materials and workmanship. The warranty DOES NOT COVER MALFUCTIONS RESULTING FROM NEGLECT, MISUSE, ABUSE OR MODIFICATIONS TO THE BOARD OR FAILTURE TO FOLLOW ALL SAFETY AND USE WARNINGS CONTAINDED HERIN.

Important Safety information

READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO OPERATE YOUR ELECTRIC SKATEBOARD
The combination of power and weight makes the ELECTRIC SKATEBOARD a potentially hazardous device. Improper use can result in property damage, serious injury, or even death. Understanding all of its features and controls is the key to safe riding. Avoid uneven surface, potholes, surface cracks, and obstacles. Always ride at a safe speed, maintaining full control over the board at all times. Adult supervision is strongly recommended.

NOT FOR CHILDREN UNDER 14.

Electric Skateboard SAFETY WARNING
The board does not conform to Motor Vehicle Standards is not intended for operation on the public streets, roads, or highways. Serious injury can result from the unsafe operation of this vehicle. The operator can minimize these assumed risks by wearing safety equipment. Always check your local laws before use.

HELMETS, PROTECTIVE EYEWEAR, APPROPRIATE FOOTWEAR, WRIST, KNEE, AND ELBOW PROTECION MUST BE WORN AT ALL TIMES. DO NOT OPERATE THE ELECTRIC SKATEBOARD IN TRAFFIC ON WET, FROZEN, OILY, OR UNPAVED SURFACES. DO NOT OPERATE NEAR PEOPLE OR EVEN VEHICLES.

OPERATION WARNING

  • This product is designed for use by children ages 14 and up.
  • The Electric Skateboards maximum recommended weight for the rider is 250 ibs. This product should not be used without adult supervision.
  • The Electric Skateboard is designed for one rider only.
  • Be aware that a strong electromagnetic field could interfere with the function of the remote control in your riding area. The user of this product and adult supervisor assumes all risks associated with its use. To minimize these assumed risks, the user MUST WEAR SAFETY HELMET, PROTECTIVE EYE WEAR, APPROPRIATE FOOTWEAR, KNEE AND ELBOW PROTECTION AT ALL TIMES.
  • Do not operate your Electric Skateboard in crowded areas.
  • NOTE: IF YOUR DO NOT UNDERSTAND ANY AND ALL PARTS OF THIS SAFETY OPERATION INFORMATION, PLEASE CALL THE SKATEBOARD WARRANTY SERVICE TO CLARIFY ALL POINTS IN THIS OWNER’S MANUAL.

Safety Tips

READ THESE IMPORTANT SAFETY INSTRUCTIONS CAREFULLY BEFORE RIDING THE BOARD!

This electric skateboard is not a toy. Understanding all of its features and controls is essential for safe riding. As with most sports there are certain risks and dangers associated with skateboarding that may result in severe bodily injuries. The rider can minimize these assumed risks by wearing proper safety gear and following our safety instructions listed here. Rider understands that he/she must abide by local laws and regulations when riding the skateboard. Local laws should be consulted for specific requirements in your area for riding of this board as laws differ by location.

Riding Your Skateboard:

  • Our Skateboard is designed for use by responsible riders ages 14 and up.
  • This board must be operated by only one rider at a time.
  • User’s weight should be within skateboard’s max load capacity.
  • Young riders should not use this skateboard without adult supervision.
  • This board is not intended for operation on public streets, roads or highways.
  • Always check your city laws to determine local requirements before using in public areas.
  • **WEAR A HELMET & PROTECTIVE GEAR AT ALL TIMES! This includes elbow and kneepads and proper footwear.
  • Inspect the skateboard before using it to make sure that it is safe to use and in riding order.
  • Always ride at a safe speed, maintaining full control over the board and yourself at all time.
  • Always start off slowly, never pull trigger too hard from still position, its dangerous!
  • Do not ride outside your ability. If you have doubts about your ability to ride, DO NOT RIDE IT!
  • Do not operate the electric skateboard in traffic or on wet, loose gravel, frozen, uneven or oily surfaces, or near people or other vehicles.
  • Ride only on relatively smooth, hard surfaces. Only our 800W electric skateboard can be ridden on grass and gravel.
  • Avoid potholes, surface cracks and obstacles.
  • Do not attempt to do anything which may cause death or injury to yourself or others.
  • Should not be used for tricks, jumps, ramps, grinds, rough handling and prolonged steep hills.
  • Always slow down and brake appropriately when approaching or overtaking pedestrians.
  • Never hitch a ride from a car, bicycle, etc.
  • Do not operate under the influence of drugs or alcohol.

How To Fall

  • Falling is part of skateboarding therefore knowing how to fall without getting seriously injured in important.
  • Learning to fall correctly can help prevent serious injury- practice falling on a soft surface or grass.
  • If you are losing your balance, crouch down as low as you can on your skateboard so that you will not have as far to fall.
  • In a fall, the idea is to land on the fleshy parts of your body.
  • If you fall, pull your arms, elbow and hands into your chest then land on your shoulders and roll your body.
  • Make your body more relaxed when you fall rather than go stiff because you’re less likely to get injured than if you fall with stiff joints.

Using Your Remote Controller

  • Our remote controller is equipped with a 3-position speed switch, slow (front)/medium (middle)/fast (back). Always start by using the beginner-mode (slow position).
  • Our remote control has a very sensitive trigger, so accelerate slowly and smoothly.
  • Adjusting the speed down to slow position is strongly recommended for new 1st time electric skateboarders.

Charging Your Battery

  • Completely charge the battery before use
  • The batteries are fully charged when the light on the charger turns from red to green.
  • Maintain your battery well by keeping it fully charged when not in use to prolong battery life.
  • Your charger is designed to automatically stop charging when the batteries are fully charged, so it’s ok to leave your boards battery plugged in all the time if you’re riding it regularly. Do not attempt to use the charger if it has been dropped or damaged.
  • Never attempt to charge a damaged battery or frozen battery.
  • Do not operate the charger if the cord or plug is damaged.
  • Do not use the charger in a closed area or poorly-ventilated area.
  • Do not ever use the electric skateboard battery to power or recharge any other equipment.
  • Keep children away from the electric skateboard while it is being recharged.

Maintaining Your Skateboard

  • Ensure that the deck remains dry at all time. If your board gets wet dry it as soon as possible.
  • Check all nuts, bolts and mounted components to ensure that they are tight. v
  • Be sure that the wheel nuts on the skateboard are tightened properly.
  • Check the condition of the wheels to be sure that they are smooth and even.
  • Stop using the product immediately if any part becomes loose. Tighten loose nuts and bolts until you encounter resistance and then stop. Do not over tighten these parts.

By purchasing any product from this website directly or indirectly, purchaser and user assume all risks, responsibility and liability for use of this product, including any resulting loss or damage to persons or property. Purchaser or user understands that they must abide by provincial or state laws and be in proper physical condition to ride this electric skateboard. You should not buy any product from Skates unless you agree to these terms. Skates will not accept any responsible for any accident, injury or death caused by carelessness or improper use of skateboards. Under no circumstance should you perform any modification to your purchase which may include but not limited to, increasing the power, modifying the motor, upgrading the motor, changing the design of the product, interfering with the computer management system or circumnavigating any safety feature, doing so will increase your chances of injury. If you have any question or concerns feel free to contact us at 1800-337-7276 / Int’l +(1)647-996-9094.

Essential Skateboarding Safety Instructions | Skatetek

SAFETY TIPS

READ THESE IMPORTANT SAFETY INSTRUCTIONS CAREFULLY BEFORE RIDING THE BOARD!

This electric skateboard is not a toy. Understanding all of its features and controls is essential for safe riding. As with most sports there are certain risks and dangers associated with skateboarding that may result in severe bodily injuries. The rider can minimize these assumed risks by wearing proper safety gear and following our safety instructions listed here. Rider understands that he/she must abide by local laws and regulations when riding the skateboard. Local laws should be consulted for specific requirements in your area for riding of this board as laws differ by location.

Riding Your Skateboard:

  • Our Skateboard is designed for use by responsible riders ages 14 and up
  • This board must be operated by only one rider at a time.
  • User’s weight should be within skateboard’s max load capacity.
  • Young riders should not use this skateboard without adult supervision.
  • This board is not intended for operation on public streets, roads or highways.
  • Always check your city laws to determine local requirements before using in public areas.
  • **WEAR A HELMET & PROTECTIVE GEAR AT ALL TIMES! This includes elbow and kneepads and proper footwear.
  • Inspect the skateboard before using it to make sure that it is safe to use and in riding order.
  • Always ride at a safe speed, maintaining full control over the board and yourself at all time.
  • Always start off slowly, never pull trigger too hard from still position, its dangerous!
  • Do not ride outside your ability. If you have doubts about your ability to ride, DO NOT RIDE IT!
  • Do not operate the electric skateboard in traffic or on wet, loose gravel, frozen, uneven or oily surfaces, or near people or other vehicles.
  • Ride only on relatively smooth, hard surfaces. Only our 1200 Watt- 3500 Watt electric skateboard can be ridden on grass and gravel.
  • Avoid potholes, surface cracks and obstacles.
  • Do not attempt to do anything which may cause death or injury to yourself or others.
  • Should not be used for tricks, jumps, ramps, grinds, rough handling and prolonged steep hills.
  • Always slow down and brake appropriately when approaching or overtaking pedestrians.
  • Never hitch a ride from a car, bicycle, etc.
  • Do not operate under the influence of drugs or alcohol.

How To Fall

  • Falling is part of skateboarding therefore knowing how to fall without getting seriously injured in important.
  • Learning to fall correctly can help prevent serious injury- practice falling on a soft surface or grass.
  • If you are losing your balance, crouch down as low as you can on your skateboard so that you will not have as far to fall.
  • In a fall, the idea is to land on the fleshy parts of your body.
  • If you fall, pull your arms, elbow and hands into your chest then land on your shoulders and roll your body.
  • Make your body more relaxed when you fall rather than go stiff because you’re less likely to get injured than if you fall with stiff joints.

Using Your Remote Controller

  • Our remote controller is equipped with a 3-position speed switch, slow (front)/medium (middle)/fast (back). Always start by using the beginner-mode (slow position).
  • Our remote control has a very sensitive trigger, so accelerate slowly and smoothly.
  • Adjusting the speed down to slow position is strongly recommended for new 1st time electric skateboarders.

Charging Your Battery

  • Completely charge the battery before use
  • The batteries are fully charged when the light on the charger turns from red to green.
  • Maintain your battery well by keeping it fully charged when not in use to prolong battery life.
  • Your smart charger is designed to automatically stop charging when the batteries are fully charged, so it’s ok to leave your boards battery plugged in all the time if you’re riding it regularly. Do not attempt to use the charger if it has been dropped or damaged.
  • Never attempt to charge a damaged battery or frozen battery.
  • Do not operate the charger if the cord or plug is damaged.
  • Do not use the charger in a closed area or poorly-ventilated area.
  • Do not ever use the electric skateboard battery to power or recharge any other equipment.
  • Keep children away from the electric skateboard while it is being recharged.

Maintaining Your Skateboard

  • Ensure that the deck remains dry at all time. If your board gets wet dry it as soon as possible.
  • Check all nuts, bolts and mounted components to ensure that they are tight.
  • Be sure that the wheel nuts on the skateboard are tightened properly.
  • Check the condition of the wheels to be sure that they are smooth and even.
  • Stop using the product immediately if any part becomes loose. Tighten loose nuts and bolts until you encounter resistance and then stop. Do not over tighten these parts.

By purchasing any product from this website directly or indirectly, purchaser and user assume all risks, responsibility and liability for use of this product, including any resulting loss or damage to persons or property. Purchaser or user understands that they must abide by provincial or state laws and be in proper physical condition to ride this electric skateboard. You should not buy any product from Skatetek unless you agree to these terms. Skatetek will not accept any responsible for any accident, injury or death caused by carelessness or improper use of skateboards. Under no circumstance should you perform any modification to your purchase which may include but not limited to, increasing the power, modifying the motor, upgrading the motor, changing the design of the product, interfering with the computer management system or circumnavigating any safety feature, doing so will increase your chances of injury. If you have any question or concerns feel free to contact us at 1800-3377-276 / Int’l +(1)647 996 9094.

Skatetek Return & Refund Policy on Skateboard Shop Online

RETURN POLICY

Defective Products

If there is a manufacture defect under warranty within terms of the warranty, the purchased product can be returned to us for repair or replacement, providing it is in its original shape and package and accompanied with the original proof of purchase. Your warranty period starts from the date of purchase or confirmed delivery to you. Warranty shipping cost is the responsibility of the customer.

Incorrect Address or Refused Shipments

If you provided us with an inaccurate shipping address or the shipment was refused by the recipient and your order is returned to us by the shipping company, we will refund your purchase minus a 20% restocking fee and original shipping charges and will also deduct additional shipping charges for the return (as charged to us by the shipping company). We count on your to provide the correct shipping address for your order therefore please be sure provide us with the correct and complete shipping address for your order.

Damaged Shipments

Each of our board is inspected prior to dispatch to our customers to make sure that no board leaves damaged. If you find your purchased product to be damaged in any way on delivery to you, we require that you notify us by e-mail or call within 48 hours of receipt providing a detailed and full description of the problem and we will issue a Return Authorization Number. Promptly return the product to us including a fully completed Returns Form. Once we receive the returned product and if the returned item is proved to be damaged we will replace your order immediately. Please ensure the returned product is securely packaged and well protected.

Lost or Missing Shipments

Lost or missing shipments must be reported to Skatetek within a week of the expected delivery date. Should our shipping company show the lost or missing package as delivered, you will need to sign an affidavit attesting to the fact that the package was indeed not received by you. Any unreported lost or missing shipments are the responsibility of the customer and Skatetek shall assume no liability for unreported missing or lost shipments.

Shipping Errors

It is our intention to process each order with 100% accuracy. If there is a shipping error on our part related to your order, please accept our sincere apologies in advance. Please call or e-mail us immediately to report the error. We will organize to pick up the incorrect product and send out the correct replacement product at our cost. Please note we do not offer refunds if through this process you change your mind.

How to Return a Product

Please call us or e-mail us to receive a Return Authorization Number before returning any order. You must send us a fully completed return form with any returned product. All unauthorized returns will be refused, you must contact us first to return any item, and simply shipping the item back to us can result in lost packages or additional processing charges that will be the responsibility of the customer. All returned items must be in its original shape and original manufacture’s packaging and accompanied with the original proof of purchase. If the product is not returned to us with all of the original packaging or if is not in “as-new” conditions, it will be sent back to you. No partial returns will be accepted. All items must be returned with shipping pre-paid. Under no circumstances is user-damaged product returnable. We don’t accept any product if it is not in its original brand new condition or missing parts, or has signs of use or misuse, or is not suitable for resale. On returned product the shipping and handling fee will not be refunded (unless the return is a result of our error on our part).

Questions

If you have further questions regarding returning a product, please feel free to send as an e-mail or call us at 1800-337-7276 or +(1) 647 996 9094

Buy Skateboards Online | Shipping and Delivery Almost Every Country

SHIPPING AND DELIVERY

Shipping Information :

Canada – $75, Parts – $30

  • We ship to almost every country in the world.
  • Shipments are made within 24-48 hours of order.
  • When you place an order, we will estimate shipping and delivery dates for you based on the shipping options you choose.
  • Your shipping costs depend upon the shipping methods and shipping destination.
  • The date you receive your order will depend on the shipping method you select.
  • Orders are shipped and delivered on business days.
  • Receipt of payment must be received before we process your order.
  • We will send you a confirmation e-mail or call you when your order has shipped.

International Orders :

U.S.A – $95

WorldWide – $600

Depending On Location

  • Orders shipping to countries outside the Canada may be subject to brokerage fees, import taxes, customs duties and fees levied by the destination country.
  • All duties/customs and taxes are the responsibility of the recipient. Skatetek does not cover these additional charges.

Delivery Methods:

  • We will choose the appropriate way of transport at our sole discretion, unless otherwise expressly instructed by the customer.
  • Generally we deliver the product through courier.
  • All risk is transferred to the customer as soon as the goods are delivered by the forwarding agent.
  • The customer has to report any transport damages immediatel to the forwarding agent.
  • Transport damages also have to be reported to us in order to assert any claims.

Delivery Time :

  • Delivery time may be delayed, if we do not receive all the information necessary for processing your order.
  • Canada 2-5 business days
  • US 3-5 business days
  • International shipment can take up to 14 business days

Signature on Delivery :

  • Once your order arrives, make sure to inspect all components for any damage that may have occurred during shipment. Sign for the order only if the product is in an acceptable condition.

Need Shipping Quote?

  • Please call +1-647-996-9094 or e-mail us your complete shipping address along with your country and postal code to sales@skatetek.com for current shipping rates. You will be e-mailed a shipping quote based on the information provided.

Shipping Inquires :

  • Phone: +1-647-996-9094
  • Email: info@skatetek.com

Custom Center – Skatetek Electric Skateboard

Skatetek Electric Skateboard is proud to introduce its in-house custom airbrushing centre. All decks can be custom designed as per your specifications and is airbrushed by our well experienced artist, De Anne Lamirande, who has over 2 decades of experience in this field.
Please email us or call for your custom airbrushing needs.
Email: info@skatetek.com
Tel: 1800 3377 276
Cell: +1 647 996 9094

1200 Watt Wildcat Twin Drive Electric Skateboard | Skatetek

Skatetek Wildcat 1200w Twin Drive

$1,899.00

  • Deck Style: Indonesian Bamboo (Optional Customized Deck Design Available)
  • Motor Power: 1200 watt (High Torque) (2 x 600w Independent Motors)
  • Maximum Speed: ≤ 44km/hr (27 mph)
  • Maximum Load Capacity: 135 kg (297 Lbs)
  • Charging Time: 3-5 hours
  • Wheel Style: All Terrain Super-Grip Air Tire 6”
  • Battery Input Voltage: 90-250v
  • Battery Capacity: Lithium 18 Amp (Extended Life For Longer Use)
  • Transmission: Belt Drive (Brushless motor,Aircraft Grade)
  • Reverse Technology
  • Abs Regenerative Brakes
  • Starter: Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed) Blue Tooth Technology
  • Auto Power Shut Off: Yes

Independent Spring Suspension Trucks With newly innovated stabilizers. (Aircraft Grade)ADD TO CART 

1500W Black Skullator Electric Skateboard | Skatetek

1500W Skullator Electric Skateboard

$1,799.005.003out of 5

  • Deck Style: Canadian Maple Wood customized Airbrushed Skull Design
  • Motor Power: 1500 watt (High Torque)
  • Maximum Speed: ≤ 50km/hr (31 mph)
  • Maximum Load Capacity: 150 kg (330 Lbs)
  • Charging Time: 3-5 hours
  • Wheel Style: All Terrain Super-grip Air Tire
  • Battery Input Voltage: 90-250v
  • Battery Capacity: Lithium 20 Amp (Extended Life For Longer Use)
  • Transmission: Belt Drive (Brushless motor, Aircraft Grade
  • Reverse Technology
  • Abs Regenerative Brakes
  • Starter: Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed) Blue Tooth Technology
  • Auto Power Shut Off: Yes
  • Independent Spring Suspension Trucks With newly innovated stablizers. (Aircraft Grade)
  • Weight Of Complete Board With Battery : 28 kg / 61 Lbs

ADD TO CART 

Skatetek’s Skullator 1500 Watt Electric Skateboard is one of the Best All Terrain Electric Skateboard, ever engineered by a Canadian company. We have used the the finest aircraft grade components available on the market for the Skullator, which makes it number one in the world today. The Skullator is upgraded in so many ways, compared to other brands on the market, that anyone can learn to ride it in a matter of minutes. The Skullator also boasts a number of key safety features and comes standard with L.E.D headlights for those Knight Riders. The Skullator 1500 is currently the fastest production all terrain skateboard on the market. The upgraded lithium battery pack on the Skullitor will give you hours of riding pleasure. Hand designed and airbrushed deck by our professional artist. This amazing board goes just about anywhere. It Fast on the Streets and furious on the trails.

1500W Blue Skullator Electric Skateboard | Skatetek

Skatetek’s Skullator 1500 Watt Electric Skateboard is one of the Best All Terrain Electric Skateboard, ever engineered by a Canadian company. We have used the the finest aircraft grade components available on the market for the Skullator, which makes it number one in the world today. The Skullator is upgraded in so many ways, compared to other brands on the market, that anyone can learn to ride it in a matter of minutes. The Skullator also boasts a number of key safety features and comes standard with L.E.D headlights for those Knight Riders. The Skullator 1500 is currently the fastest production all terrain skateboard on the market. The upgraded lithium battery pack on the Skullitor will give you hours of riding pleasure. Hand designed and airbrushed deck by our professional artist. This amazing board goes just about anywhere. It Fast on the Streets and furious on the trails.

1500W Skullator Electric Skateboard

$1,799.005.002out of 5

  • Deck Style: Canadian Maple Wood customized Airbrushed Skull Design
  • Motor Power: 1500 watt (High Torque)
  • Maximum Speed: ≤ 50km/hr (31 mph)
  • Maximum Load Capacity: 150 kg (330 Lbs)
  • Charging Time: 3-5 hours
  • Wheel Style: All Terrain Super-grip Air Tire
  • Battery Input Voltage: 90-250v
  • Battery Capacity: Lithium 20 Amp (Extended Life For Longer Use)
  • Transmission: Belt Drive (Brushless motor, Aircraft Grade
  • Reverse Technology
  • Abs Regenerative Brakes
  • Starter: Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed) Blue Tooth Technology
  • Auto Power Shut Off: Yes
  • Independent Spring Suspension Trucks With newly innovated stablizers. (Aircraft Grade)
  • Weight Of Complete Board With Battery : 28 kg / 61 Lbs

ADD TO CART 

1500W Yellow Skullator Electric Skateboard | Skatetek

Skatetek’s Skullator 1500 Watt Electric Skateboard is one of the Best All Terrain Electric Skateboard, ever engineered by a Canadian company. We have used the the finest aircraft grade components available on the market for the Skullator, which makes it number one in the world today. The Skullator is upgraded in so many ways, compared to other brands on the market, that anyone can learn to ride it in a matter of minutes. The Skullator also boasts a number of key safety features and comes standard with L.E.D headlights for those Knight Riders. The Skullator 1500 is currently the fastest production all terrain skateboard on the market. The upgraded lithium battery pack on the Skullitor will give you hours of riding pleasure. Hand designed and airbrushed deck by our professional artist. This amazing board goes just about anywhere. It Fast on the Streets and furious on the trails.

1500W Skullator Electric Skateboard

$1,799.005.001out of 5

  • Deck Style: Canadian Maple Wood customized Airbrushed Skull Design
  • Motor Power: 1500 watt (High Torque)
  • Maximum Speed: ≤ 50km/hr (31 mph)
  • Maximum Load Capacity: 150 kg (330 Lbs)
  • Charging Time: 3-5 hours
  • Wheel Style: All Terrain Super-grip Air Tire
  • Battery Input Voltage: 90-250v
  • Battery Capacity: Lithium 20 Amp (Extended Life For Longer Use)
  • Transmission: Belt Drive (Brushless motor, Aircraft Grade
  • Reverse Technology
  • Abs Regenerative Brakes
  • Starter: Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed) Blue Tooth Technology
  • Auto Power Shut Off: Yes
  • Independent Spring Suspension Trucks With newly innovated stablizers. (Aircraft Grade)
  • Weight Of Complete Board With Battery : 28 kg / 61 Lbs

ADD TO CART 

Skatetek Lynx 1000w | Electric & Motorized Slatetek

Skatetek Lynx 1000w

$1,599.005.007out of 5

  • Deck Style: Indonesian Bamboo (Optional Customized Deck Design Available)
  • Motor Power: 1000 watt (High Torque)
  • Maximum Speed: ≤ 38km/hr (24 mph)
  • Maximum Load Capacity: 135 kg (297 Lbs)
  • Charging Time: 3-5 hours
  • Wheel Style: Partial Terrain Super-Grip Air Tire 6”
  • Battery Input Voltage: 90-250v
  • Battery Capacity: Lithium 14 Amp (Extended Life For Longer Use)
  • Transmission: Belt Drive (Brushless motor,Aircraft Grade)
  • Reverse Technology
  • Abs Regenerative Brakes
  • Starter: Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed) Blue Tooth Technology
  • Auto Power Shut Off: Yes

Tortion Trucks With newly innovated stabilizers. (Aircraft Grade)

Total weight incl battery pack 33 LbsADD TO CART 

The Raptor 3500Watt Twin Drive|Electric Skateboard

The Raptor 3500Watt Twin Drive

$2,299.005.002out of 5

Skatetek Is Once Again Proud To Introduce Its latest 2015 Electric Skateboard Edition

Deck Style: Indonesian Bamboo With Glass Fibre Composite

  • Motor Power: 3500 watt (High Torque) Twin Motor
  • Maximum Speed: ≤ 60 km/h (37 Miles)
  • Maximum Load Capacity: 150 kg (330 Lbs)
  • Charging Time: 3-5 hours
  • Wheel Style: All Terrain Super-grip Air Tire (8”)
  • Battery Capacity: Sony Lithium 18 Amp Smart Battery (With Digital Batt Meter)
  • Transmission: Belt Drive (Brushless motor, Aircraft Grade)
  • Abs Regenerative Brakes
  • Starter: Latest Technology 3G Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed) Blue Tooth Technology
  • Auto Power Shut Off: Yes
  • Aluminium Magnesium Alloy Trucks Double Springs
  • Weight Of Complete Board With Battery : 11.9 kg / 26 Lbs
  • Velcro Foot Straps (Easy Off, Easy On)
  • Board Dims: 110 x 40 x 20 Cm
  • Climbing Angle +- 35 Degrees

PRE-ORDERS NOW OPEN, Allow 4-6 weeks for deliveryADD TO CART 

1200W Eagle Electric Skateboard | Skatetek

1200W Eagle Electric Skateboard

$1,699.005.002out of 5

  • Deck Style: Wood Finish (Optional Customised Deck Design Available)
  • Motor Power: 1200 watt
  • Maximum Speed: ≤ 44km/hr (27 mph)
  • Maximum Load Capacity: 135 kg (297 lbs)
  • Charging Time: 3-6 hours
  • Wheel Style: Air Tire
  • Battery Input Voltage: 90-250v
  • Battery Capacity: Lithium 18 A
  • Transmission: Belt (Brushless motor)
  • Reverse Technology
  • Starter: Interference-free Wireless Remote Controller + 2 Adjustable Speed Settings (Low And High speed)
  • Auto Power Shut Off: Yes
  • Independent Spring Suspension Trucks With newly innovated stablizers.

ADD TO CART 

Skatetek Electric Skateboards are proud to introduce its new flagship Eagle series 1200 watt all terrain electric skateboard with reverse technology-limited edition. This high tech electric skateboard is capable of incredible torque and power with standard abs braking. The Eagle comes standard with independent spring suspension trucks and lithium powered battery pack that allows constant power. Skatetek also boasts the only company known to supply the Eagle 1200 watt. The Eagle also has an upgraded computer controlled microprocessor that’s ensures smooth power, torque and safe braking at high speeds. The wireless remote is also a new upgraded from its previous models. This beast is a must for atv trails and off-road enthusiasts.Our Latest innovative feature is a truck stabilizer that ensures smooth safer riding at high speeds.